-- Network Working Group T. Brown
-- Request for Comments: 1694 K. Tesink
-- Obsoletes: 1304 Editors
-- Category: Standards Track Bell Communications Research
-- August 1994
--
--
-- Definitions of Managed Objects
-- for SMDS Interfaces using SMIv2
--SIP-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Counter32,Integer32,IpAddressFROM SNMPv2-SMI
TimeStamp,TEXTUAL-CONVENTIONFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
transmission, ifIndex, mib-2 FROM RFC1213-MIB;-- This is the MIB module for the SMDS Interface objects.sipMIB MODULE-IDENTITYLAST-UPDATED"9403311818Z"ORGANIZATION"IETF Interfaces Working Group"CONTACT-INFO" Tracy Brown
Postal: Bell Communications Research
331 Newman Springs Road
P.O. Box 7020
Red Bank, NJ 07701-7020
US
Tel: +1 908 758-2107
Fax: +1 908 758-4177
E-mail: tacox@mail.bellcore.com
Kaj Tesink
Postal: Bell Communications Research
331 Newman Springs Road
P.O. Box 7020
Red Bank, NJ 07701-7020
US
Tel: +1 908 758 5254
Fax: +1 908 758 4177
E-mail: kaj@cc.bellcore.com."DESCRIPTION"The MIB module to describe
SMDS interfaces objects."::={ mib-2 36}SMDSAddress::=TEXTUAL-CONVENTIONDISPLAY-HINT"1h:"STATUScurrentDESCRIPTION"The 60-bit SMDS address,
preceded by 4 bits with the following values:
1100 when representing an individual address
1110 when representing a group address."SYNTAXOCTETSTRING(SIZE(8))IfIndex::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The value of this object identifies the
interface for which this entry contains
management information. The value of this
object for a particular interface has the same
value as the ifIndex object, defined in RFC
1213, for the same interface."
SYNTAXInteger32sip OBJECTIDENTIFIER::={ transmission 31}sipMIBObjects OBJECTIDENTIFIER::={ sipMIB 1}-- The SIP Level 3 GroupsipL3Table OBJECT-TYPESYNTAXSEQUENCEOF SipL3Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains SIP L3 parameters and
state variables, one entry per SIPL3 interface."::={ sip 1}sipL3Entry OBJECT-TYPESYNTAX SipL3Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This list contains SIP L3 parameters and
state variables."INDEX{ sipL3Index }::={ sipL3Table 1}
SipL3Entry ::=SEQUENCE{
sipL3Index IfIndex,
sipL3ReceivedIndividualDAs Counter32,
sipL3ReceivedGAs Counter32,
sipL3UnrecognizedIndividualDAs Counter32,
sipL3UnrecognizedGAs Counter32,
sipL3SentIndividualDAs Counter32,
sipL3SentGAs Counter32,
sipL3Errors Counter32,
sipL3InvalidSMDSAddressTypes Counter32,
sipL3VersionSupport Integer32}sipL3Index OBJECT-TYPESYNTAXIfIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the SIP
L3 interface for which this entry contains
management information. "::={ sipL3Entry 1}sipL3ReceivedIndividualDAs OBJECT-TYPESYNTAXCounter32
MAX-ACCESSread-onlySTATUSdeprecated-- Moved to ifTable-- ifInUcastPkts defined in [9] must be used instead.DESCRIPTION"The total number of individually addressed SIP
Level 3 PDUs received from the remote system
across the SNI. The total includes only
unerrored L3PDUs."::={ sipL3Entry 2}sipL3ReceivedGAs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUSdeprecated-- Moved to ifTable-- ifInMulticastPkts defined in [9] must be used instead.DESCRIPTION"The total number of group addressed SIP Level 3
PDUs received from the remote system across the
SNI. The total includes only unerrored L3PDUs."::={ sipL3Entry 3}sipL3UnrecognizedIndividualDAs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION
"The number of SIP Level 3 PDUs received from the
remote system with invalid or unknown individual
destination addresses (Destination Address
Screening violations are not included). See SMDS
Subscription MIB module."::={ sipL3Entry 4}sipL3UnrecognizedGAs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"The number of SIP Level 3 PDUs received from the
remote system with invalid or unknown group
addresses. (Destination Address Screening
violations are not included). See SMDS
Subscription MIB module."::={ sipL3Entry 5}sipL3SentIndividualDAs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUSdeprecated-- Moved to ifTable-- ifOutUcastPkts defined in [9] must be used instead.DESCRIPTION"The number of individually addressed SIP Level 3
PDUs that have been sent by this system across the
SNI."::={ sipL3Entry 6}sipL3SentGAs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUSdeprecated-- Moved to ifTable-- ifOutMulticastPkts defined in [9] must be used instead.DESCRIPTION"The number of group addressed SIP L3PDUs that
have been sent by this system across the SNI."::={ sipL3Entry 7}-- The total number of SIP L3PDU errors can be calculated as-- (Syntactic errors + Semantic Service errors )-- Syntactic errors include:-- sipL3Errors-- Latest occurrences of syntactic error types are logged in-- sipL3PDUErrorTable.-- Semantic Service errors include:-- sipL3UnrecognizedIndividualDAs-- sipL3UnrecognizedGAs-- sipL3InvalidSMDSAddressTypes-- Note that public networks supporting SMDS may discard-- SIP L3PDUs due to subscription violations. Related-- managed objects are defined in Definitions of Managed-- Objects for SMDS Subscription.
sipL3Errors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUSdeprecated-- Moved to ifTable-- ifInErrors defined in [9] must be used instead.DESCRIPTION"The total number of SIP Level 3 PDUs received
from the remote system that were discovered to
have errors (including protocol processing and bit
errors but excluding addressing-related errors)
and were discarded. Includes both group addressed
L3PDUs and L3PDUs containing an individual
destination address."::={ sipL3Entry 8}sipL3InvalidSMDSAddressTypes OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUSdeprecated-- Moved to ifTable-- ifInUnknownProtos defined in [9] must be used instead.DESCRIPTION"The number of SIP Level 3 PDUs received from the
remote system that had the Source or Destination
Address_Type subfields, (the four most significant
bits of the 64 bit address field), not equal to
the value 1100 or 1110. Also, an error is
considered to have occurred if the Address_Type
field for a Source Address, the four most
significant bits of the 64 bits, is equal to 1110
(a group address)."::={ sipL3Entry 9}sipL3VersionSupport OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A value which indicates the version(s) of SIP
that this interface supports. The value is a sum.
This sum initially takes the value zero. For each
version, V, that this interface supports, 2 raised
to (V - 1) is added to the sum. For example, a
port supporting versions 1 and 2 would have a
value of (2^(1-1)+2^(2-1))=3. The
sipL3VersionSupport is effectively a bit mask with
Version 1 equal to the least significant bit
(LSB)."::={ sipL3Entry 10}-- The SIP Level 2 GroupsipL2Table OBJECT-TYPESYNTAXSEQUENCEOF SipL2Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains SIP L2PDU parameters and
state variables, one entry per SIP L2 interface."::={ sip 2}sipL2Entry OBJECT-TYPESYNTAX SipL2Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This list contains SIP L2 parameters and state
variables."INDEX{ sipL2Index }::={ sipL2Table 1}
SipL2Entry ::=SEQUENCE{
sipL2Index IfIndex,
sipL2ReceivedCounts Counter32,
sipL2SentCounts Counter32,
sipL2HcsOrCRCErrors Counter32,
sipL2PayloadLengthErrors Counter32,
sipL2SequenceNumberErrors Counter32,
sipL2MidCurrentlyActiveErrors Counter32,
sipL2BomOrSSMsMIDErrors Counter32,
sipL2EomsMIDErrors Counter32}
sipL2Index OBJECT-TYPESYNTAXIfIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the SIP
interface for which this entry contains management
information."::={ sipL2Entry 1}sipL2ReceivedCounts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of SIP Level 2 PDUs received from the
remote system across the SNI. The total includes
only unerrored L2PDUs."::={ sipL2Entry 2}sipL2SentCounts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of SIP Level 2 PDUs that have been
sent by this system across the SNI."::={ sipL2Entry 3}
-- The following error types are counted, and-- preclude sipL2ReceivedCounts to be incremented:-- sipL2HcsOrCRCErrors-- sipL2PayloadLengthErrors-- sipL2SequenceNumberErrors-- sipL2BomOrSSMsMIDErrors-- sipL2EomsMIDErrors-- The receipt of SIP Level 2 PDUs which are BOMs and-- for with a MID that is already active will cause-- sipL2MidCurrentlyActiveErrors to increment.-- Any already accumulated (correct) segmentation-- units are discarded.The sipL2ReceivedCounts-- is incremented by 1. Thus,-- sipL2ReceivedCounts defines the number of-- correct SIP Level 2 PDUs delivered to the reassembly-- process.sipL2HcsOrCRCErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of received SIP Level 2 PDUs that were
discovered to have either a Header Check Sequence
error or a Payload CRC violation."::={ sipL2Entry 4}sipL2PayloadLengthErrors OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of received SIP Level 2 PDUs that had
Payload Length errors that fall in the following
specifications:
- SSM L2_PDU payload length field value less
- than 28 octets or greater than 44 octets,
- BOM or COM L2_PDU payload length field not
- equal to 44 octets,
- EOM L2_PDU payload length field value less
- than 4 octets or greater than 44 octets."::={ sipL2Entry 5}sipL2SequenceNumberErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of received SIP Level 2 PDUs that had
a sequence number within the L2PDU not equal to
the expected sequence number of the SMDS SS
receive process."::={ sipL2Entry 6}sipL2MidCurrentlyActiveErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The number of received SIP Level 2 PDUs that are
BOMs for which an active receive process is
already started."::={ sipL2Entry 7}sipL2BomOrSSMsMIDErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of received SIP Level 2 PDUs that are
SSMs with a MID not equal to zero or are BOMs with
MIDs equal to zero."::={ sipL2Entry 8}sipL2EomsMIDErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of received SIP Level 2 PDUs that are
EOMs for which there is no active receive process
for the MID (i.e., the receipt of an EOM which
does not correspond to a BOM) OR the EOM has a MID
equal to zero."::={ sipL2Entry 9}
-- The SIP PLCP GroupsipPLCP OBJECTIDENTIFIER::={ sip 3}-- The DS1 PLCP GroupsipDS1PLCPTable OBJECT-TYPESYNTAXSEQUENCEOF SipDS1PLCPEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains SIP DS1 PLCP parameters and
state variables, one entry per SIP port."::={ sipPLCP 1}sipDS1PLCPEntry OBJECT-TYPESYNTAX SipDS1PLCPEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This list contains SIP DS1 PLCP parameters and
state variables."INDEX{ sipDS1PLCPIndex }::={ sipDS1PLCPTable 1}
SipDS1PLCPEntry ::=SEQUENCE{
sipDS1PLCPIndex IfIndex,
sipDS1PLCPSEFSs Counter32,
sipDS1PLCPAlarmState INTEGER,
sipDS1PLCPUASs Counter32}sipDS1PLCPIndex OBJECT-TYPESYNTAXIfIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the
interface for which this entry contains management
information. "::={ sipDS1PLCPEntry 1}sipDS1PLCPSEFSs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A DS1 Severely Errored Framing Second (SEFS) is a
count of one-second intervals containing one or
more SEF events. A Severely Errored Framing (SEF)
event is declared when an error in the A1 octet
and an error in the A2 octet of a framing octet
pair (i.e., errors in both framing octets), or two
consecutive invalid and/or nonsequential Path
Overhead Identifier octets are detected."::={ sipDS1PLCPEntry 2}
sipDS1PLCPAlarmState OBJECT-TYPESYNTAXINTEGER{noAlarm (1),receivedFarEndAlarm (2),incomingLOF (3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable indicates if there is an alarm
present for the DS1 PLCP. The value
receivedFarEndAlarm means that the DS1 PLCP has
received an incoming Yellow Signal, the value
incomingLOF means that the DS1 PLCP has declared a
loss of frame (LOF) failure condition, and the
value noAlarm means that there are no alarms
present. See TR-TSV-000773 for a description of
alarm states."::={ sipDS1PLCPEntry 3}sipDS1PLCPUASs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The counter associated with the number of
Unavailable Seconds, as defined by TR-TSV-000773,
encountered by the PLCP."::={ sipDS1PLCPEntry 4}-- The DS3 PLCP GroupsipDS3PLCPTable OBJECT-TYPESYNTAXSEQUENCEOF SipDS3PLCPEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains SIP DS3 PLCP parameters and
state variables, one entry per SIP port."::={ sipPLCP 2}sipDS3PLCPEntry OBJECT-TYPESYNTAX SipDS3PLCPEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This list contains SIP DS3 PLCP parameters and
state variables."INDEX{ sipDS3PLCPIndex }::={ sipDS3PLCPTable 1}
SipDS3PLCPEntry ::=SEQUENCE{
sipDS3PLCPIndex IfIndex,
sipDS3PLCPSEFSs Counter32,
sipDS3PLCPAlarmState INTEGER,
sipDS3PLCPUASs Counter32}sipDS3PLCPIndex OBJECT-TYPESYNTAXIfIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the
interface for which this entry contains management
information. "::={ sipDS3PLCPEntry 1}sipDS3PLCPSEFSs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A DS3 Severely Errored Framing Second (SEFS) is a
count of one-second intervals containing one or
more SEF events. A Severely Errored Framing (SEF)
event is declared when an error in the A1 octet
and an error in the A2 octet of a framing octet
pair (i.e., errors in both framing octets), or two
consecutive invalid and/or nonsequential Path
Overhead Identifier octets are detected."::={ sipDS3PLCPEntry 2}
sipDS3PLCPAlarmState OBJECT-TYPESYNTAXINTEGER{noAlarm (1),receivedFarEndAlarm (2),incomingLOF (3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable indicates if there is an alarm
present for the DS3 PLCP. The value
receivedFarEndAlarm means that the DS3 PLCP has
received an incoming Yellow Signal, the value
incomingLOF means that the DS3 PLCP has declared a
loss of frame (LOF) failure condition, and the
value noAlarm means that there are no alarms
present. See TR-TSV-000773 for a description of
alarm states."::={ sipDS3PLCPEntry 3}sipDS3PLCPUASs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The counter associated with the number of
Unavailable Seconds, as defined by TR-TSV-000773,
encountered by the PLCP."::={ sipDS3PLCPEntry 4}-- The SMDS Applications group-- Applications that have been identified for this group are:-- * IP-over-SMDS (details are specified in RFC 1209)smdsApplications OBJECTIDENTIFIER::={ sip 4}ipOverSMDS OBJECTIDENTIFIER::={ smdsApplications 1}-- Although the objects in this group are read-only, at the-- agent's discretion they may be made read-write so that the-- management station, when appropriately authorized, may-- change the addressing information related to the-- configuration of a logical IP subnetwork implemented on-- top of SMDS.-- This table is necessary to support RFC1209 (IP-over-SMDS)-- and gives information on the Group Addresses and ARP-- Addresses used in the Logical IP subnetwork.-- One SMDS address may be associated with multiple IP-- addresses. One SNI may be associated with multiple LISs.
ipOverSMDSTable OBJECT-TYPESYNTAXSEQUENCEOF IpOverSMDSEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The table of addressing information relevant to
this entity's IP addresses."::={ ipOverSMDS 1}ipOverSMDSEntry OBJECT-TYPESYNTAX IpOverSMDSEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The addressing information for one of this
entity's IP addresses."INDEX{ ipOverSMDSIndex, ipOverSMDSAddress }::={ ipOverSMDSTable 1}
IpOverSMDSEntry ::=SEQUENCE{
ipOverSMDSIndex IfIndex,
ipOverSMDSAddress IpAddress,
ipOverSMDSHA SMDSAddress,
ipOverSMDSLISGA SMDSAddress,
ipOverSMDSARPReq SMDSAddress}ipOverSMDSIndex OBJECT-TYPESYNTAXIfIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the
interface for which this entry contains management
information. "::={ ipOverSMDSEntry 1}ipOverSMDSAddress OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The IP address to which this entry's addressing
information pertains."::={ ipOverSMDSEntry 2}ipOverSMDSHA OBJECT-TYPESYNTAXSMDSAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The SMDS Individual address of the IP station."
::={ ipOverSMDSEntry 3}ipOverSMDSLISGA OBJECT-TYPESYNTAXSMDSAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The SMDS Group Address that has been configured
to identify the SMDS Subscriber-Network Interfaces
(SNIs) of all members of the Logical IP Subnetwork
(LIS) connected to the network supporting SMDS."::={ ipOverSMDSEntry 4}ipOverSMDSARPReq OBJECT-TYPESYNTAXSMDSAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The SMDS address (individual or group) to which
ARP Requests are to be sent."::={ ipOverSMDSEntry 5}-- The SMDS Carrier Selection group-- This group is used as a place holder-- for carrier selection objects.smdsCarrierSelection OBJECTIDENTIFIER::={ sip 5}
-- The SIP Error LogsipErrorLog OBJECTIDENTIFIER::={ sip 6}sipL3PDUErrorTable OBJECT-TYPESYNTAXSEQUENCEOF SipL3PDUErrorEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table that contains the latest occurrence of
the following syntactical SIP L3PDU errors:
- Destination Address Field Format Error,
The following pertains to the 60 least significant
bits of the 64 bit address field. The 60 bits
contained in the address subfield can be used to
represent addresses up to 15 decimal digits. Each
decimal digit shall be encoded into four bits
using Binary Coded Decimal (BCD), with the most
significant digit occurring left-most. If not all
15 digits are required, then the remainder of this
field shall be padded on the right with bits set
to one. An error is considered to have occurred:
a). if the first four bits of the address
subfield are not BCD, OR b). if the first four
bits of the address subfield are populated with
the country code value 0001, AND the 40 bits which
follow are not Binary Coded Decimal (BCD) encoded
values of the 10 digit addresses, OR the remaining
16 least significant bits are not populated with
1's, OR c). if the address subfield is not
correct according to another numbering plan which
is dependent upon the carrier assigning the
numbers and offering SMDS.
- Source Address Field Format Error,
The description of this parameter is the same as
the description of the Destination Address Field
Format Error.
- Invalid BAsize Field Value,
An error is considered to have occurred when the
BAsize field of an SIP L3PDU contains a value less
that 32, greater than 9220 octets without the
CRC32 field present, greater than 9224 octets with
the CRC32 field present, or not equal to a
multiple of 4 octets,
- Invalid Header Extension Length Field Value,
An error is considered to have occurred when the
Header Extension Length field value is not equal
3.
- Invalid Header Extension - Element Length,
An error is considered to have occurred when the
Header Extension - Element Length is greater than
12.
- Invalid Header Extension - Version Element
Position, Length, or Value,
An error is considered to have occurred when a
Version element with Length=3, Type=0, and Value=1
does not appear first within the Header Extension,
or an element Type=0 appears somewhere other than
within the first three octets in the Header
Extension.
- Invalid Header Extension - Carrier Selection
Element Position, Length, Value or Format,
An error is considered to have occurred when a
Carrier Selection element does not appear second
within the Header Extension, if the Element Type
does not equal 1, the Element Length does not
equal 4, 6, or 8, the Element Value field is not
four BCD encoded decimal digits used in specifying
the Carrier Identification Code (CIC), or the
identified CIC code is invalid.
- Header Extension PAD Error
An error is considered to have occurred when the
Header Extension PAD is 9 octets in length, or if
the Header Extension PAD is greater than zero
octets in length and the Header Extension PAD does
not follow all Header Extension elements or does
not begin with at least one octet of all zeros.
- BEtag Mismatch Error,
An error is considered to have occurred when the
Beginning-End Tags in the SIP L3PDU header and
trailer are not equal.
- BAsize Field not equal to Length Field Error,
An error is considered to have occurred when the
value of the BAsize Field does not equal the value
of the Length Field.
- Incorrect Length Error, and
An error is considered to have occurred when the
the Length field value is not equal to the portion
of the SIP L3PDU which extends from the
Destination Address field up to and including the
CRC32 field (if present) or up to and including
the PAD field (if the CRC32 field is not present).
As an optional check, an error is considered to
have occurred when the length of a partially
received SIP L3PDU exceeds the BAsize value.
- MRI Timeout Error.
An error is considered to have occurred when the
elapsed time between receipt of BOM and
corresponding EOM exceeds the value of the MRI
(Message Receive Interval) for a particular
transport signal format.
An entry is indexed by interface number and error
type, and contains Source Address, Destination
Address and a timestamp. All these errors are
counted in the sipL3Errors counter. When
sipL3PDUErrorTimeStamp is equal to zero, the
SipL3PDUErrorEntry does not contain any valid
information."::={ sipErrorLog 1}sipL3PDUErrorEntry OBJECT-TYPESYNTAX SipL3PDUErrorEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the service disagreement table."INDEX{ sipL3PDUErrorIndex, sipL3PDUErrorType }::={ sipL3PDUErrorTable 1}
SipL3PDUErrorEntry ::=SEQUENCE{
sipL3PDUErrorIndex IfIndex,
sipL3PDUErrorType INTEGER,
sipL3PDUErrorSA SMDSAddress,
sipL3PDUErrorDA SMDSAddress,
sipL3PDUErrorTimeStamp TimeStamp}sipL3PDUErrorIndex OBJECT-TYPESYNTAXIfIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the
interface for which this entry contains management
information."::={ sipL3PDUErrorEntry 1}sipL3PDUErrorType OBJECT-TYPESYNTAXINTEGER{erroredDAFieldFormat (1),erroredSAFieldFormat (2),invalidBAsizeFieldValue (3),invalidHdrExtLength (4),invalidHdrExtElementLength (5),invalidHdrExtVersionElementPositionLenthOrValue (6),
invalidHdrExtCarSelectElementPositionLenghtValueOrFormat (7),hePADError (8),beTagMismatch (9),baSizeFieldNotEqualToLengthField (10),incorrectLength (11),mriTimeout (12)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The type of error."::={ sipL3PDUErrorEntry 2}sipL3PDUErrorSA OBJECT-TYPESYNTAXSMDSAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A rejected SMDS source address."::={ sipL3PDUErrorEntry 3}sipL3PDUErrorDA OBJECT-TYPESYNTAXSMDSAddress
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A rejected SMDS destination address."::={ sipL3PDUErrorEntry 4}sipL3PDUErrorTimeStamp OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The timestamp for the service disagreement. The
timestamp contains the value of sysUpTime at the
latest occurrence of this type of service
disagreement. See textual description under
sipL3PDUErrorTable for boundary conditions."::={ sipL3PDUErrorEntry 5}-- The DXI GroupsipDxiTable OBJECT-TYPESYNTAXSEQUENCEOF SipDxiEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The DXI table."::={ sipMIBObjects 1}
sipDxiEntry OBJECT-TYPESYNTAX SipDxiEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the DXI table."INDEX{ ifIndex }::={ sipDxiTable 1}
SipDxiEntry ::=SEQUENCE{
sipDxiCrc
INTEGER,
sipDxiOutDiscards
Counter32,
sipDxiInErrors
Counter32,
sipDxiInAborts
Counter32,
sipDxiInTestFrames
Counter32,
sipDxiOutTestFrames
Counter32,
sipDxiHbpNoAcks
Counter32}sipDxiCrc OBJECT-TYPESYNTAXINTEGER{crc16(1),crc32(2)
}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object indicates the type
of Frame Checksum used by DXI. Current
choices include CCITT CRC16 or CRC32."::={ sipDxiEntry 1}sipDxiOutDiscards OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of outbound frames discarded
because of congestion."::={ sipDxiEntry 2}sipDxiInErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of inbound frames discarded
because of errors such as frame checksum
(CRC) violations,
non-integral number of octets, address
and control field violations, and frame
size errors."::={ sipDxiEntry 3}
sipDxiInAborts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of inbound frames discarded
because of an abort bit sequence (1111111)
received before closing flag."::={ sipDxiEntry 4}sipDxiInTestFrames OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of unerrored,
inbound Test frames received
(generally as part of Heart
Beat Poll procedure)."::={ sipDxiEntry 5}sipDxiOutTestFrames OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of unerrored,
outbound Test frames sent
(generally as part of Heart
Beat Poll procedure)."::={ sipDxiEntry 6}sipDxiHbpNoAcks OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Heart Beat
Poll (HBP) No Ack timeouts."::={ sipDxiEntry 7}-- conformance informationsmdsConformance OBJECTIDENTIFIER::={ sipMIB 2}smdsGroups OBJECTIDENTIFIER::={ smdsConformance 1}smdsCompliances OBJECTIDENTIFIER::={ smdsConformance 2}-- compliance statementssmdsCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for SMDS interfaces."
MODULE-- this moduleMANDATORY-GROUPS{ sipLevel3Stuff }GROUP sipLevel2Stuff
DESCRIPTION"This group is mandatory only for those
interfaces (SNIs) which run SIP Level 2."GROUP sipDS1PLCPStuff
DESCRIPTION"This group is mandatory only for those
interfaces (SNIs) which run the DS1 PLCP."GROUP sipDS3PLCPStuff
DESCRIPTION"This group is mandatory only for those
interfaces (SNIs) which run the DS3 PLCP."GROUP sipIPApplicationsStuff
DESCRIPTION"This group is mandatory only for interfaces
operating IP over SMDS in accordance with
RFC1209."GROUP sipDxiStuff
DESCRIPTION"This group is mandatory only for those interfaces
(DXI-SNI)
which run the DXI protocol."::={ smdsCompliances 1}-- units of conformancesipLevel3Stuff OBJECT-GROUPOBJECTS{ sipL3Index,
sipL3VersionSupport, sipL3PDUErrorIndex,
sipL3PDUErrorType,
sipL3PDUErrorSA, sipL3PDUErrorDA,
sipL3PDUErrorTimeStamp }STATUScurrentDESCRIPTION"A collection of objects providing information
applicable to all SMDS interfaces."::={ smdsGroups 1}sipLevel2Stuff OBJECT-GROUPOBJECTS{ sipL2Index, sipL2HcsOrCRCErrors,
sipL2PayloadLengthErrors,
sipL2SequenceNumberErrors,
sipL2MidCurrentlyActiveErrors,
sipL2BomOrSSMsMIDErrors,
sipL2EomsMIDErrors }STATUScurrentDESCRIPTION"A collection of objects providing information
specific to interfaces using the SIP Level 2."::={ smdsGroups 2}sipDS1PLCPStuff OBJECT-GROUPOBJECTS{ sipDS1PLCPIndex, sipDS1PLCPSEFSs,
sipDS1PLCPAlarmState, sipDS1PLCPUASs }STATUScurrentDESCRIPTION"A collection of objects providing information
specific to interfaces using the DS1 PLCP."::={ smdsGroups 3}sipDS3PLCPStuff OBJECT-GROUPOBJECTS{ sipDS3PLCPIndex, sipDS3PLCPSEFSs,
sipDS3PLCPAlarmState, sipDS3PLCPUASs }STATUScurrentDESCRIPTION"A collection of objects providing information
specific to interfaces using the DS3 PLCP."::={ smdsGroups 4}sipIPApplicationsStuff OBJECT-GROUPOBJECTS{ ipOverSMDSIndex, ipOverSMDSAddress,
ipOverSMDSHA, ipOverSMDSLISGA, ipOverSMDSARPReq }STATUScurrentDESCRIPTION"A collection of objects providing information
for running IP over SMDS."::={ smdsGroups 5}sipDxiStuff OBJECT-GROUPOBJECTS{ sipDxiCrc, sipDxiOutDiscards,
sipDxiInErrors, sipDxiInAborts,
sipDxiInTestFrames, sipDxiOutTestFrames,
sipDxiHbpNoAcks }STATUScurrentDESCRIPTION"A collection of objects providing information
specific to interfaces using the DXI protocol."::={ smdsGroups 6}END